Replace the fender

Replace the taillight Du liest Schutzblech ersetzen 3 Minuten Continue Replace the display
Tags

Schutzblech ersetzen / tauschen

In dieser Anleitung zeigen wir dir Schritt für Schritt, wie du das Schutzblech an deinem VMAX E-Scooter VX2 Hub / VX2 Gear selbst tauschen kannst.

Model VX2 Hub / VX2 Gear
Time required approx.30 minutes
Difficulty Medium

Tools needed

  • 3 mm Allen wrench
  • 2.5 mm Allen wrench
  • Phillips screwdriver
  • Ersatzteil: Schutzblech
Before you begin, make sure your VMAX E-Scooter is E-Scooter . Work on a stable surface and have all your tools within easy reach.

Instructions

1

Remove the side covers

Remove the rear side panels

Remove both rear side panels. To do this, use a 3 mm Allen wrench to loosen the three screws on each side.

Be sure to set the screws aside neatly so that nothing gets lost during reassembly.

2

Loosen the side struts

Loosen the side struts of the fender

Loosen the two side struts of the fender using a 2.5 mm Allen wrench.

3

Detach the fender from the mounting arm

Detach the fender from the mounting arm

Using a 3 mm Allen wrench, loosen the two screws on each side that secure the fender to the mounting arm.

4

Remove the fender

Disconnect the connector

Disconnect the plug on the taillight.

Remove the fender

Then carefully remove the fender.

5

Remove the taillight

Unplug the cable

Remove the cable from the cable guide, then use a Phillips-head screwdriver to loosen the screw on the taillight.

Remove the taillight from the fender

Carefully pull the taillight out from behind the fender.

6

Rücklicht ins neue Schutzblech einsetzen

Rücklicht einsetzen und befestigen

Setze das bestehende Rücklicht in das neue Schutzblech ein und befestige es mit der Kreuzschraube.

7

Run the cables and install the fender

Lege das Kabel wieder in die Kabelführung ein und positioniere das neue Schutzblech korrekt.

First, tighten the four screws on the mounting arm (3 mm Allen key), then tighten the side struts using the 2.5 mm Allen key.

8

Make the connection and install the covers

Reconnect the tail light's plug. Then reattach the side covers on both sides using the 3 mm Allen wrench.

When assembling the unit, make sure that all screws are tightened properly and that no cables are pinched or damaged.

Check the result

After assembly, check to make sure the taillight is working properly. Turn E-Scooter your VMAX E-Scooter and check that the taillight and brake light respond reliably.

E-Scooter repairs, test your VMAX E-Scooter carefully while stationary or over a short distance before using it normally again in your daily routine.

Frequently Asked Questions

Hier findest du Antworten auf häufige Fragen zum Schutzblech-Tausch.

Muss ich das Rücklicht ersetzen?

Nein, das Rücklicht wird nicht ersetzt. Es wird ausgebaut und im neuen Schutzblech wieder eingesetzt.

Why isn't my taillight working after I installed it?

First, check the connector. In most cases, the cable isn't connected properly or isn't fully seated.

Das Schutzblech sitzt nicht richtig – was tun?

Kontrolliere, ob alle Schrauben korrekt positioniert sind und das Schutzblech sauber am Halterarm anliegt, bevor du es festziehst.

Do I need to remove both side panels?

Yes, that's the only way to get to all the bolts and remove the fender without any tension.

If you're unsure or need help, our local service teams are here to assist you.